Tag: UTCU3

Posted on by

MMS FLEX: FCA Marelli 11GF

Bench Solution for FCA Marelli 11GF

Release 7.48.0.0 of Flex allows you to Bench program FCA engine control units equipped on mild hybrid systems, extending intervention possibilities on a more modern range of vehicles.

With protocol for Marelli 11GF you can perform engine calibration operations in order to improve performance, as well as restore and clone ECUs without the need to open the unit.

It’s super easy: read the full backup of the damaged unit and transfer data to a working unit. No need to have both vehicles inside the workshop.

FCA Marelli 11GF TC277 Read/Write/Checksum Calculation Internal Flash, Read/Write Internal EEPROM, Read/Write External EEPROM, Full Backup

Some of the supported vehicles:

  • Fiat 500 (332) 1.0L FireFly MHEV 68HP
  • Fiat Panda (312) 1.0L FireFly MHEV 68HP
  • Lancia Ypsilon (846) 1.0L FireFly MHEV 68HP

This new protocol is available for the following software packages:

  • FLS0.1M – SW Flex ECU (car, van, bike) OBD/Bench Master
  • FLS0.1S – SW Flex ECU (car, van, bike) OBD/Bench Slave
  • FLS0.5M – SW Flex Full Master
  • FLS0.5S – SW Flex Full Slave
  • FLS0.10M – SW Flex Bench/Boot Infineon TC17xx / TC2xx / TC3xx Master
  • FLS0.10S – SW Flex Bench/Boot Infineon TC17xx / TC2xx / TC3xx Slave

 

Posted on by

MMS FLEX: Ford UTCU3

Fomoco UTCU3 TCUs Now Covered

New version 7.47.0.0 of Flex out now, introducing a new protocol dedicated to Fomoco UTCU3 TCUs installed on Ford vehicles with 6, 8, and 10-speed automatic transmissions.

With the new Flex release, you can perform OBD programming of a wide range of vehicles that are equipped with this control unit, by connecting directly to the diagnostic port.

Operating in OBD means getting quick access to the map area, making it possible to carry out necessary modifications to optimize transmission performance.

Ford Fomoco UTCU3 TC277 Read/Write/Checksum Calculation Maps

Some of the supported vehicles:

  • Ford Bronco (VI) (2020MY) 2.7L Ecoboost V6 335PS

  • Ford Kuga (III) (2020MY) 1.5L EcoBoost 150PS

  • Ford Ranger T6 (2019MY) 2.3L Ecoboost 270PS

This new protocol is available for the following software packages:

  • FLS0.2M – SW Flex TCU OBD/Bench Master
  • FLS0.2S – SW Flex TCU OBD/Bench Slave
  • FLS0.5M – SW Flex Full Master
  • FLS0.5S – SW Flex Full Slave

 

Posted on by

bFlash Update V1912A – Porsche SDI21 full OBD!

Porsche SDI21 full OBD!!

This protocol allows virtual reading and writing of the engine(s) found below:

4 cyl : 2.0T & 2.5T (718)
6 cyl : 3.0T & 3.8T (991.2)
Also includes the new 991.2 GT2RS

Q&A

How do I connect to the ECU?
You connect directly through the OBD socket.

 

Do I need to unlock the ECU first?
No BOOT or BENCH unlock is required. Unlock is done over OBD!

 

How fast is it ?
Reading is a Virtual Read in a matter of seconds.
The write time is around 7 min.(approx) for the first time.
Next calibration update is done in 1 min. 30 seconds. (approx)

 

Can I use file read with other tools?
As a dummy proof protection feature, you can only use bFlash watermarked vread’s.
Never try to program BOOT read or virtual read from other tools!

 

What control units (TCU’s) are included in this bFlash update?
You can find the full list of control units below.

New OBD Protocols:

PORSCHE
SIEMENS SDI21 TC1791

More Info
Posted on by

bFlash Update V1911B – Magnetti Marelli BOOT!

Magnetti Marelli Protocols in BOOTMODE!

These new protocols allow read and write of the engines found below:

1.3 MJet EU5/6
2.3 MJet EU5/6
1.4 TJet EU5/6

Q&A

How fast is it ?
The write time is around 1 minute.
Reading is a Full Read and takes approximately 3-4 minutes.

 

Can I clone the ECU ?
Yes, full ECU cloning is possible.

 

How do I connect to the ECU ?
You can use the help function in bFlash and it will show you the pinout of the ECU.

 

What control units (TCU’s) are included in this bFlash update?
You can find the full list of control units below.

New BOOT Protocols:

ABARTH
Marelli 8GMF MPC5565
Marelli 8GMK MPC5640

ALFA ROMEO
Marelli 8F3 MPC5565
Marelli 9DF MPC5644
Marelli 8GMF MPC5565
Marelli 8GMK MPC5640

FIAT
Marelli 8F3 MPC5565
Marelli 9DF MPC5644
Marelli 8GMF MPC5565
Marelli 8GMK MPC5640

LANCIA
Marelli 8F3 MPC5565
Marelli 9DF MPC5644
Marelli 8GMF MPC5565
Marelli 8GMK MPC5640

JEEP
Marelli 8F3 MPC5565
Marelli 9DF MPC5644
Marelli 8GMF MPC5565
Marelli 8GMK MPC5640

More Info
Posted on by

bFlash Update V1911A – FORD TCU OBD!

Ford 8 & 10 speed Gearbox Protocols by OBD!

These new protocols allow read and write of the Transmission Unit’s in the latest Ford F-150 & Ford Raptor 3.5 EcoBoost with 10 speed transmission or the new Focus 1.5 TDCi with 8 speed automatic.

Q&A

Do I need to buy an extra bFlash module ?
Of course not! This protocol is active now, for all our active users.

 

How fast is it ?
The write time is around 3 min 30 seconds.
Reading is a Virtual Read in a matter of seconds.

 

How do I connect to the TCU ?
You can just connect directly to the OBD socket of the car.

 

What control units (TCU’s) are included in this bFlash update?
You can find the full list of control units below.

New OBD Protocols:

FORD
UTCU3 TC277 10R80
UTCU3 TC277 8F35

More Info