Posted on by

DFOX: Renault / Nissan EMS3142

New OBD/BENCH driver for Continental & Vitesco EMS3142

With the new DFOX® V2 2.0.1598 update, the coverage of control units has been further expanded.
OBD and BENCH support is now available for EMS3142 engine control units installed on Renault, Nissan, Dacia, and Mitsubishi cars.

If the car has SGW system (Security Gateway), use the D48CB03 cable to perform the bypass according to the manuals provided.
The Bench driver also allows you to work on a bench via PINOUT, for direct management of the motor electronics.

Available features:

  • Reading
  • Writing
  • Recovery
  • Checksum

Supported models:

  • Dacia Dokker 1.0L TCe
  • Dacia Duster 1.0L ECO-G
  • Dacia Duster 1.0L TCe
  • Dacia Sandero 1.0 ECO-G III
  • Mitsubishi Colt 1.0 MPI VII
  • Nissan Juke 1.0 DIG-T
  • Nissan Micra 1.0 DIG-T
  • Renault Captur 1.0 TCe,
  • Renault Captur 0.9 TCe J5
  • Renault Clio V 1.0 TCe
  • Renault Clio Twingo V 1.0 SCe

DFOX Info >>
DFOX Updates >>

Posted on by

MMS FLEX: OBD Mode for EMS2910 / EMS2916

EMS2910 / EMS2916 OBD Released!

New protocol released in version 7.44.0.0 of Flex out now for Vitesco EMS2910 and EMS2916 engine units installed on new generation Ford vehicles.

This new protocol allows programming operations on vehicles with 2.0L EcoBoost, 2.3L EcoBoost, and 1.0L MHEV engines.

Access the map zone via OBD and make your modifications directly via the diagnostic port, safely and quickly: no need to open or ship the unit to our labs.

New Protocols:

  • Ford Vitesco EMS2910 TC387 Read/Write/Checksum Calculation Maps and ASW
  • Ford Vitesco EMS2916 TC387 Read/Write/Checksum Calculation Maps and ASW

Some of the supported vehicles:

  • Ford Mustang (VII-S650) 2.3L EcoBoost 100PS
  • Ford Bronco (VI) 2.0L EcoBoost 250PS
  • Ford Puma (I) 1.0L EcoBoost MHEV 140PS

This new protocol is available for the following software packages:

  • FLS0.1M – SW Flex ECU (car, van, bike) OBD/Bench Master
  • FLS0.1S – SW Flex ECU (car, van, bike) OBD/Bench Slave
  • FLS0.5M – SW Flex Full Master
  • FLS0.5S – SW Flex Full Slave

 

Posted on by

MMS FLEX: OBD Mode for SID213 and SID213EVO

SID213 / SID213 EVO OBD Programming!

New protocol released in version 7.43.0.0 of Flex for Conti SID213 and SID213EVO engine units installed on new gen Ford and Volkswagen vehicles.

This new solution is made to work on vehicles with 2.0L EcoBlue and 2.0L TDI engines.

A new protocol that opens access to the map area via OBD connection, therefore you can now make your modifications via the diagnostic port, safely and quickly: no need to open the unit or ship it to our labs.

New Protocols:

  • Ford/VW Continental SID213 TC387 Read/Write/Checksum Calculation Maps
  • Ford/VW Continental SID213EVO TC387 Read/Write/Checksum Calculation Maps

Some of the supported vehicles:

  • Ford Ranger WildTrak (IV) 2.0L 16v EcoBlue 205PS+
  • Volkswagen Amarok 2.0L TDI

This new protocol is available for the following software packages:

  • FLS0.1M – SW Flex ECU (car, van, bike) OBD/Bench Master
  • FLS0.1S – SW Flex ECU (car, van, bike) OBD/Bench Slave
  • FLS0.5M – SW Flex Full Master
  • FLS0.5S – SW Flex Full Slave

 

Posted on by

I/O Terminal XMAS Promo!

I/O Terminal XMAS SALE now live!

No promo code necessary, reductions have been directly applied.

Offer valid until January 31st!

Visit Store

Posted on by

VF2 Flasher v2.9.3.5

Dear clients and friends we are very pleased to announce UNLOCK services for MD1CS069 control units fitted to CASE / FIAT / IVECO / LANDINI / MITSUBISHI FUSO / NEW HOLLAND and STEYR vans, tractors and other industrial vehicles. This is a service provided exclusively to our clients, owners of a VF2 Flasher, as a mail-in service to GTD headquarters in Portugal. The service usually takes 2-3 business days but as some of you already know we’ve been processing KIA / HYUNDAI MD1CS012; PSA MD1CS003 / MG1CS042 and BMW MD1CS001 / MD1CP032 / MG1CS024 / MG1CS049 / MG1CS201 control units the same day! As usual you may contact support for further details. Please do note that the service will be limited during the next 23-26 and 31 December and 1-2 of the new year!

BENCH (Service Mode)

  • CASE MD1CS069 TC299: Read ( Int. Flash + Int. Eeprom + All[Backup] ) + Write ( Int. Flash + Int. Eeprom + All[Backup] ) / Recovery / Checksum(s)
  • FIAT MD1CS069 TC299: Read ( Int. Flash + Int. Eeprom + All[Backup] ) + Write ( Int. Flash + Int. Eeprom + All[Backup] ) / Recovery / Checksum(s)
  • IVECO MD1CS069 TC299: Read ( Int. Flash + Int. Eeprom + All[Backup] ) + Write ( Int. Flash + Int. Eeprom + All[Backup] ) / Recovery / Checksum(s)
  • LANDINI MD1CS069 TC299: Read ( Int. Flash + Int. Eeprom + All[Backup] ) + Write ( Int. Flash + Int. Eeprom + All[Backup] ) / Recovery / Checksum(s)
  • MITSUBISHI FUSO MD1CS069 TC299: Read ( Int. Flash + Int. Eeprom + All[Backup] ) + Write ( Int. Flash + Int. Eeprom + All[Backup] ) / Recovery / Checksum(s)
  • NEW HOLLAND MD1CS069 TC299: Read ( Int. Flash + Int. Eeprom + All[Backup] ) + Write ( Int. Flash + Int. Eeprom + All[Backup] ) / Recovery / Checksum(s)
  • STEYR MD1CS069 TC299: Read ( Int. Flash + Int. Eeprom + All[Backup] ) + Write ( Int. Flash + Int. Eeprom + All[Backup] ) / Recovery / Checksum(s)

VIDEO:

More info and pricing

Posted on by

Alientech Winter Season Offers

Alientech Winter Seasonal Offers!

KESS3:

  • 40% OFF Master & Slave Activations
  • 40% OFF Upgrade from Slave to Master
  • 20% OFF TCU Protocols Activation
  • 20% OFF Online Backup Management
  • 20% OFF DynoDrive Activation
  • 10% OFF Subscription Renewals
  • 40% OFF Additional Subscription Alignment Fee

ECM Titanium:

  • 30% OFF Activations and Upgrades
  • 40% OFF Driver Credits
  • 40% OFF Driver Maker Plugin
  • 10% OFF Subscription Renewals
Shop & Save Now

 

All prices excludes sales taxes (where applicable)

This offer is valid until 12th January 2026.

Posted on by

KESS3: Citroen AMI / Fiat Topolino / Opel Rocks-e

AEVPT VCU3000 – Citroën, Fiat, Opel/Vauxhall.

Work in BOOT mode on the new VCU units for EVs, now supported.

With this update you can operate directly on the memory of the EVPT VCU3000 control unit, installed on ultra-compact electric vehicles from Citroën, Fiat and Opel/Vauxhall with 5.5 kWh power units from 2025 onward.

The BOOT connection guarantees full access to the VCU data, enabling complete read and write operations for accurate parameter management and full control over your tuning workflow. A solution designed for workshops beginning to work on the new generation of micro-EVs.

Thanks to the support for Citroën Ami, Fiat Topolino and Opel/Vauxhall Rocks-e, you can expand your service offering to include electric vehicles increasingly common in urban environments, providing specialist and high-value services.

Technical focus

  • Connection: BOOT

  • ECU: EVPT VCU3000

  • Production years: from 2025

  • Brands involved: Citroën, Fiat, Opel, Vauxhall

Supported vehicles

  • Citroën Ami

  • Fiat Topolino,

  • Opel Rocks-e

  • Vauxhall Rocks-e

Shop KESS3 Now
Posted on by

BitSoftware Black Friday Sale!

We can offer 20% discounts on BitBox and BitEdit software activations until 1st December!

Use the coupon code bitsoftsale at checkout.

To see other BLACK FRIDAY promotions, click here.


The BitSoftware team are responsible for producing software packages designed for chiptuning beginners and professionals.

They currently offer 2 platforms:

bitbox_logo

 

BitBox – Software for reading and writing control unit memories.

 

 

BitEdit_logo

 

BitEdit – Software for editing calibrations within control unit maps.

 

 

Both software packages are managed by a Senselock USB dongle protection system, all software modules can be activated on a single dongle. The program has a client-server architecture needs to be connected to the Internet.