This cable allows you to connect most flash tools to Temic DSG DQ200 controllers and can be used to read out the original file direct from the DSG connector as reading over OBD is not possible.
It can be used to read/write all versions of DQ200 on the bench.
The cable has both K-line and CAN wired (with integral termination resistor) and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.
This cable allows you to connect most flash tools to Temic DSG DQ250 controllers. This can be used to read out the original file direct from the DSG connector as reading over OBD in tricore versions of DQ250 is not possible (type Exx and Fxx).
It can also be used to read/write all versions of DQ250 on the bench (type Cxx, Exx and Fxx).
The cable has both K-line and CAN wired (with integral termination resistor) and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.
This BDM Style probe allows reading/writing of Continental SID807 control units with TC1797 processor without soldering.
No additional resistors or boot pins are required!
It handles all connections to the ecu and connects directly to the CMDFlash Boot Interface. It can be used to read/write the FLASH/EEPROM memory over Boot Strap Loader. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
This BDM Style probe allows reading/writing of Continental SID807 control units with TC1796 processor without soldering.
No additional resistors or boot pins are required!
It handles all connections to the ecu and connects directly to the CMDFlash Boot Interface. It can be used to read/write the FLASH/EEPROM memory over Boot Strap Loader. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
This BDM Style probe allows reading/writing of DEUTZ / FENDT / VALTRA EDC17CV44 and EDC17CV56 control units without soldering.
No additional resistors or boot pins are required!
It connects directly to the CMDFlash Boot Interface. It can be used to read/write password over “OBD” communication and also to read/write the IROM/EEPROM memory over Boot Strap Loader mode by the flick of a switch. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
This BDM Style probe allows reading/writing of VAG MED17.5.2 control units without soldering.
No additional resistors or boot pins are required!
It connects directly to the CMDFlash Boot Interface. It can be used to read/write password over “OBD” communication and also to read/write the IROM/EEPROM memory over Boot Strap Loader mode by the flick of a switch.LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
This kit provides a clean connection to ecu boot pads without soldering!
Simply screw the plate to the control unit and align the boot pins with the corresponding pads on the ecu. The arms are secured with high performance magnets ensuring no movement once aligned.
Each kit includes an ECU mounting plate and 2 x arms equipped with spring loaded boot pins. It is suitable for ecu’s with up to 2 connections.
* The cable pictured above is not included in the kit. Specific ecu cables can be supplied upon request. *
This BDM Style probe allows reading/writing of VAG / Porsche EDC17CP44 control units without soldering.
No additional resistors or boot pins are required!
It is supplied with a special cable to connect the ecu directly to the CMDFlash Boot Interface. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
This kit includes the CP44 probe and cable.
This BDM Style probe allows unlocking of VAG SIMOS PCR control units on the bench without soldering.
No additional resistors or boot pins are required!
It is supplied with a special cable to connect the ecu directly to the CMDFlash Boot Interface. Power is supplied by your existing CMD BDM/Tricore power supply.This kit includes the PCR probe and 2 x cables.
This BDM Style probe allows reading/writing of VAG EDC17C46 control units without soldering.
No additional resistors or boot pins are required!
It connects directly to the CMDFlash Boot Interface. It can be used to read/write password over “OBD” communication and also to read/write the IROM/EEPROM memory over Boot Strap Loader mode by the flick of a switch.LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
