Posted on

ByteShooter V3.33 / V4.05

ByteShooter V3.33 Update: For users without V4x

  • MEDC17 checksum changes (Modul 030 required)
  • Nissan Qashqai RSA
  • Jaguar XF RSA
  • Evoque SI4 RSA
  • Honda 2.0D EDC17 RSA

New:
New security from hard and software until firmware 1.24->
Firmware detection until V2.00->
Extended modulmonitoring (009, 030->)

Modified:

  • Read/write speed CAN/K-Line.
  • Reset time modified for TC1797

—————————————————————————————————————–

ByteShooter V4.05 Update:
NEW:

  • EDC17C49 CHK (Module 030 required)
  • Honda 2.2 CDTI EDC17 2013 – TC1796 (Module 030 required)
  • SID 208 Bootpw for new ECUs (Module 030 required)
  • MB ME9.7 ID/W/CHK 2MB – BETA
    Preparation for the original file read from a virtual database where the ECU does not support READ (ME9.7, ME2.8x, EDC15M, ME7.9.1 usw).

Firmware detection until V2.00->
Extended modulmonitoring (009, 030->)

Modified:

  • Read/write speed CAN/K-Line.
  • Reset time modified for TC1797
Posted on

Universal OBD to DQ200 DSG Tricore Cable

This cable allows you to connect most flash tools to Temic DSG DQ200 controllers and can be used to read out the original file direct from the DSG connector as reading over OBD is not possible.

It can be used to read/write all versions of DQ200 on the bench.

The cable has both K-line and CAN wired (with integral termination resistor) and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.

 

Posted on

Universal OBD to DQ250 DSG Tricore Cable

This cable allows you to connect most flash tools to Temic DSG DQ250 controllers. This can be used to read out the original file direct from the DSG connector as reading over OBD in tricore versions of DQ250 is not possible (type Exx and Fxx).

It can also be used to read/write all versions of DQ250 on the bench (type Cxx, Exx and Fxx).

The cable has both K-line and CAN wired (with integral termination resistor) and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.

 

Posted on

MEDC17 Tricore Boot Pin Kit – No More Soldering!

This kit provides a clean connection to ecu boot pads without soldering!

Simply screw the plate to the control unit and align the boot pins with the corresponding pads on the ecu. The arms are secured with high performance magnets ensuring no movement once aligned.

Each kit includes an ECU mounting plate and 2 x arms equipped with spring loaded boot pins. It is suitable for ecu’s with up to 2 connections.

* The cable pictured above is not included in the kit. Specific ecu cables can be supplied upon request. *

Posted on

ByteShooter Module 30 – Bosch MEDC17 Tricore Bootmode inc TP8/10

Module 30 is used for Bosch MEDC17 controllers using password protected TriCore TC17xx processor.

This module allows the reading and writing of flash and eeprom of “almost” all BOSCH EDC17 and MED17 by toolbox. With it is also possible to tune ECU’s which have a so-called Tuning-Protection 8/10. To compute to the checksum module 7 is required.

The module 30 is a pure software module. No additional hardware is included

** To open a slave “.pak” file of module 8, the matching master this module have unlocked also.

Posted on

ByteShooter Module 9 – VAG DSG DQ250 Temic TriCore

Module 9 is used for DSG controllers from Temic with TriCore processor.

Previously it was only possible to flash DSG DQ250 Temic PowerPC (Cxx software). However with module 9 it is now possible to flash also the newer generation of DSG controllers using Tricore processor.

** To open a slave “.pak” file of module 9, the matching master this module have unlocked also.

Posted on

ByteShooter Module 7 – MEDC17 OBD + Checksum

BS_modul7

Module 7 is used to read/write MEDC17 controllers without tuning protection over the OBD port.

It can also compute the checksum for all EDC17 / MED17 files read over OBD or bootmode (using seperate  Module 30). 

** Checksum function available in Master tools only!

This Module is now available free of charge in all ByteShooter tools!

Posted on

ByteShooter Module 5 – Trucks / Tractors

BS-truck_modModule 5 is for older truck and utility vehicles over the diagnostic port or on the table.

This supports the following vehicles:

  • EDC16C39 Iveco Truck
  • EDC16C8 Iveco Truck
  • EDC7C1 Iveco Truck
  • EDC7C1 New Holland Tractor
  • EDC7C3 DAF Truck
  • EDC7C3 MAN Truck
  • EDC7C32 DAF Truck
  • EDC7C32 MAN Truck
  • EDC7UC31 Doosan Machine
  • EDC7U31 Fendt Tractor
  • EDC7UC31 Iveco Truck
  • EDC7UC31 New Holland Truck
  • EDC7UC31 Valtra Tractor
  • MS6.1 MAN Truck
  • MS6.2 DAF Truck, Iveco Truck, Scania Truck
  • MS6.4 Fendt Truck), Iveco Truck, MAN Truck, New Holland Tractor, Nissan Truck

This Module is now available free of charge in all ByteShooter tools!