This cable allows you to connect most flash tools to VAG DSG DQ500 controllers. This can used to read the original file direct from the DSG connector.
Connections include power, switched ignition pin and CAN bus.
Universal OBD to DQ500 DSG Cable
Tag: cmdflash
CMDFLASH V3.2.0.124
|
CMDFLASH 07 Jun 2013 V3.2.0.124 |
OBD: VAG DSG DQ500 CAN r/vr/w/chk/recovery BOOT-TRICORE: SIEMENS SID807EVO FORD PWD READER BOSCH MED17.1.1 VAG TC1797 IROM ( i.e. S6 4.0 TFSI 420HP) |
CMDFLASH V3.2.0.123
|
CMDFLASH 23 May 2013 V3.2.0.123 |
OBD: VOLKSWAGEN POLO 1.2 3cyl 44Kw SIM11 CAN r/w/chk/recovery SEAT IBIZA 1.2 3cyl 44Kw SIM11 CAN r/w/chk/recovery SEAT IBIZA 1.2 3cyl 51Kw SIM11 CAN r/w/chk/recovery SKODA FABIA 1.2 3cyl 44Kw SIM11 CAN r/w/chk/recovery SKODA FABIA 1.2 3cyl 51Kw SIM11 CAN r/w/chk/recoveryCHEVROLET CRUZE 1.6 SRi 180CV DELCO E83 CAN r/w/chk/recovery OBD TOOLS: VAG SIEMENS PCR2.1 VAS FRF FLASHER BOOT-TRICORE: BOSCH KEFICO MEDG17.9.2 KIA/HYUNDAI ( i.e. HYUNDAI GRANDEUR 3.0GDI V6) |
CMDFlash VAG Siemens 8x Probe – SIMOS 8.3 8.4 3.0TFSI
This BDM Style probe allows unlocking of VAG SIMOS 8x control units on the bench without soldering.
No additional resistors or boot pins are required!
It is supplied with a special cable to connect the ecu directly to the CMDFlash Boot Interface. Power is supplied by your existing CMD BDM/Tricore power supply.This kit includes the Simos 8x probe and 2 x cables.
Universal OBD to DQ200 DSG Tricore Cable
This cable allows you to connect most flash tools to Temic DSG DQ200 controllers and can be used to read out the original file direct from the DSG connector as reading over OBD is not possible.
It can be used to read/write all versions of DQ200 on the bench.
The cable has both K-line and CAN wired (with integral termination resistor) and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.
Universal OBD to DQ250 DSG Tricore Cable
This cable allows you to connect most flash tools to Temic DSG DQ250 controllers. This can be used to read out the original file direct from the DSG connector as reading over OBD in tricore versions of DQ250 is not possible (type Exx and Fxx).
It can also be used to read/write all versions of DQ250 on the bench (type Cxx, Exx and Fxx).
The cable has both K-line and CAN wired (with integral termination resistor) and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.
CMDFlash PSA Peugeot Citroen SID807 TC1797 Probe
This BDM Style probe allows reading/writing of Continental SID807 control units with TC1797 processor without soldering.
No additional resistors or boot pins are required!
It handles all connections to the ecu and connects directly to the CMDFlash Boot Interface. It can be used to read/write the FLASH/EEPROM memory over Boot Strap Loader. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
CMDFlash PSA Peugeot Citroen SID807 TC1796 Probe
This BDM Style probe allows reading/writing of Continental SID807 control units with TC1796 processor without soldering.
No additional resistors or boot pins are required!
It handles all connections to the ecu and connects directly to the CMDFlash Boot Interface. It can be used to read/write the FLASH/EEPROM memory over Boot Strap Loader. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
CMDFlash DEUTZ / FENDT / VALTRA – EDC17CV44 EDC17CV56 Probe
This BDM Style probe allows reading/writing of DEUTZ / FENDT / VALTRA EDC17CV44 and EDC17CV56 control units without soldering.
No additional resistors or boot pins are required!
It connects directly to the CMDFlash Boot Interface. It can be used to read/write password over “OBD” communication and also to read/write the IROM/EEPROM memory over Boot Strap Loader mode by the flick of a switch. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
CMDFlash VAG MED17.5.2 Probe
This BDM Style probe allows reading/writing of VAG MED17.5.2 control units without soldering.
No additional resistors or boot pins are required!
It connects directly to the CMDFlash Boot Interface. It can be used to read/write password over “OBD” communication and also to read/write the IROM/EEPROM memory over Boot Strap Loader mode by the flick of a switch.LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.