This cable allows you to connect most flash tools to VAG DSG DL501 S-Tronic controllers. This can used to read the original file direct from the DSG connector.
It can be used to read all versions of DL501 on the bench.
The cable has CAN wired and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.
This BDM Style probe allows reading/writing of Continental SID208 / SID209 control units without soldering. No additional resistors or boot pins are required!
It handles all connections to the ecu and connects directly to the CMDFlash Boot Interface. It can be used to read/write the FLASH/EEPROM memory over Boot Strap Loader, also boot connections are switched to allow password reading.
LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
This universal pinout cable allows you to connect easily and comfortably to most types control units.
The cable is fitted with an OBD2 female plug allowing connection any OBD flash tool.
It features:
This cable allows you to connect most flash tools to VAG DSG DQ500 controllers. This can used to read the original file direct from the DSG connector.
Connections include power, switched ignition pin and CAN bus.
This BDM Style probe allows unlocking of VAG SIMOS 8x control units on the bench without soldering.
No additional resistors or boot pins are required!
It is supplied with a special cable to connect the ecu directly to the CMDFlash Boot Interface. Power is supplied by your existing CMD BDM/Tricore power supply.This kit includes the Simos 8x probe and 2 x cables.
This cable allows you to connect most flash tools to Temic DSG DQ200 controllers and can be used to read out the original file direct from the DSG connector as reading over OBD is not possible.
It can be used to read/write all versions of DQ200 on the bench.
The cable has both K-line and CAN wired (with integral termination resistor) and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.
This cable allows you to connect most flash tools to Temic DSG DQ250 controllers. This can be used to read out the original file direct from the DSG connector as reading over OBD in tricore versions of DQ250 is not possible (type Exx and Fxx).
It can also be used to read/write all versions of DQ250 on the bench (type Cxx, Exx and Fxx).
The cable has both K-line and CAN wired (with integral termination resistor) and is fitted with an OBD2 female plug allowing connection any flash tool with an OBD2 cable.
This BDM Style probe allows reading/writing of Continental SID807 control units with TC1797 processor without soldering.
No additional resistors or boot pins are required!
It handles all connections to the ecu and connects directly to the CMDFlash Boot Interface. It can be used to read/write the FLASH/EEPROM memory over Boot Strap Loader. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
This BDM Style probe allows reading/writing of Continental SID807 control units with TC1796 processor without soldering.
No additional resistors or boot pins are required!
It handles all connections to the ecu and connects directly to the CMDFlash Boot Interface. It can be used to read/write the FLASH/EEPROM memory over Boot Strap Loader. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
This BDM Style probe allows reading/writing of DEUTZ / FENDT / VALTRA EDC17CV44 and EDC17CV56 control units without soldering.
No additional resistors or boot pins are required!
It connects directly to the CMDFlash Boot Interface. It can be used to read/write password over “OBD” communication and also to read/write the IROM/EEPROM memory over Boot Strap Loader mode by the flick of a switch. LED lights are fitted to the underside of the probe to aid alignment, Power is supplied by your existing CMD BDM/Tricore power supply.
